QUESTION 236

An engineer configured an environment that contains the vPCand non-vPC switches, however, it was noticed that the downstream non-vPC switches do not receives the same STP bridge ID from the upstream which vPC feature must be implemented to ensure must be implemented to ensure that vPC and non-vPC switches receive the same STP bridge ID from the upstream vPC switch peers?

A.peer-switch

B.peer-gateway

C.systam-mac 0123.4567.89ab

D.vpc local role-priority 4000

Answer: A

QUESTION 237

A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between the Cisco Nexus switch and the backup server is UDP. The backup must be used when the current working configuration of the switch gets corrupted.

Which set of steps must be taken to meet these requirements?

A.1. Perform a startup-config backup to an FTP server

2. Copy startup-config in the boot flash to the running-config file

B.1. Perform a running-config backup to an SFTP server

2. Copy backup-config from the SFTP server to the running-config file

C.1. Perform a running-config backup to an SCP server

2. Copy running-config in the boot flash to the running-config file

D.1. Perform a startup-config backup to a TFTP server

2. Copy backup-config from the backup server to the running-config file

Answer: D

QUESTION 238

Refer to the exhibit. A network engineer requires remote access via SSH to a Cisco MDS 9000 Series Switch. The solution must support secure access using the local user database when the RADIUS servers are unreachable from the switches. Which command meets these requirements?

A.aaa authentication none

B.aaa authentication login default group radius

C.aaa authentication login default fallback error local

D.aaa authentication login default group local

Answer: C

QUESTION 240

A network engineer configures a converged network adapter (CNA) and must associate a virtual Fibre Channel 7 interface to VSAN 7. The CNA is connected to the interface Eth1/7, and VLAN 700 is mapped to the VSAN. Which configuration must be applied to create the virtual Fibre Channel interface and associate it with the Ethernet physical interface?

A.switch(config)# vlan 700

switch(config-vlan)# fcoe vsan 7

B.switch(config)# vsan database

switch(config-vsan)# vsan 7 interface vfc 7

C.switch(config)# interface ethernet 1/7

switch(config-if)# vfc 7 attach vlan 1,700

D.switch(config)# interface vfc 7

switch(config-if)# bind interface ethernet 1/7

Answer: D

QUESTION 241

An engineer must use the Embedded Event Manager to monitor events that occur on a cisco Nexus 9000 series switch.

An environment variable needs to be created so that several policies use the monitored events in in their actions.

The external email server is represented by IP address 10.10.10.10.

Which command sets the environment variable?

A.N9k2(config)# event manager policy environment mallserver `'10.10.10.10''

B.N9k2# event manager environment mallserver `'10.10.10.10''

C.N9k2 (config-apple1)# environment mallserver `'10.10.10.10''

D.N9k2 (config)# event manager environment mallserver `'10.10.10.10''

Answer: D

QUESTION 242

Which communication method does NFS use for requests between servers and clients?

A.XDR

B.SSC

C.RPC

D.SMB

Answer: C

QUESTION 243

A customer reports Fibre Channel login requests to a cisco MDS 9000 series Switch from an unauthorized source.

The customer requires a feature that will allow all devices already logged in and learned in and learned to be added to the Fibre channel active database.

Which two features must be enabled to accomplish this goal? (Choose two.)

A.Auto-learning

B.Port security

C.Enhanced zoning

D.Device aliases

E.Smart aliases

Answer: AB

QUESTION 244

An engineer evaluates a UI-based infrastructure management system capable of monitoring and deploying standalone VXLAN BGP EVPN deployments. The storage administrators also need the solution to manage the Cisco MDS 9000 Series Switches. Which solution meets these requirements?

A.Cisco Intersight

B.Cisco UCSD

C.Cisco Tetration

D.Cisco DCNM

Answer: D

QUESTION 245

Refer to the exhibit. Which backup operation type not include the preserve identities feature?

A.Full state

B.Logical configuration

C.System configuration

D.All configuration

Answer: A

QUESTION 246

Refer to the exhibit. Which configuration ensure that the cisco Nexus 7000 series switches are the primary devices for LACP?

A.N7K_A(config-vpc-domain)# system-priority 4000

N7K_B(config-vpc-domain)# system-priority 4000

B.N7K_A(config-vpc-domain)# system-priority 100

N7K_B(config-vpc-domain)# system-priority 200

C.N7K_A(config-vpc-domain)# system-priority 32768

N7K_B(config-vpc-domain)# system-priority 32768

D.N7K_A(config-vpc-domain)# role priority 1

N7K_B(config-vpc-domain )# role priority 2

Answer: A

QUESTION 247

A network engineer must enable port security on all Cisco MDS Series Switches in the fabric. The requirement is to avoid the extensive manual configuration of the switch ports. Which action must be taken to meet these requirements?

A.Activate CFS distribution and the auto-learning port security feature.

B.Activate CFS distribution and file auto-learning port security feature on a per-VSAN basis.

C.Enable the auto-learning port security feature on a per-VSAN basis.

D.Enable the auto-learning port security feature.

Answer: B

QUESTION 248

A network engineer is deploying a Cisco All-Flash HyperFlex solution. Which local storage configuration is required for the operating system and persistent logging?

A.Two solid state drives

B.Two SATA drives

C.One SATA drive

D.One solid state drive

Answer: A

QUESTION 249

An engineer configures the properties of a Cisco UCS Cisco Integrated Management Controller network adapter for a standalone Cisco C-Series Server. The Failback Timeout in the vNIC was set to 600. When the failure occurs, the secondary interfaces must be used and then failback when the primary interface becomes available again. Which action must be taken to meet these requirements?

A.Set default VLAN on the adapters.

B.Increase Cos to 6.

C.Disable VNTAG mode.

D.Enable Uplink failover.

Answer: D

QUESTION 250

A network engineer must prevent data comuption due to cross fabric communication in an FCoE environment. Which configuration must be applied to the Cisco Nexus Unified Switches to achieve this objective?

A.Switch(config)#fcoe fcmap 0x0efc2a

B.Switch(config-if)# no fcoe fcf-priority 0

C.Switch(config-if) # shutdown lan

D.Switch(config) # no fcoe fcf-priority

Answer: A

QUESTION 251

Which component is disrupted when the Cisco Integrated Management Controller is upgraded on a Cisco UCS Series Server?

A.Cisco UCS Manager

B.SAN traffic

C.KVM sessions

D.Data traffic

Answer: C

QUESTION 252

A company is investigating different options for IT automation tools. The IT team has experience with Python programming language and scripting using a declarative language. The proposed tool should be easy to set up and should not require installing an agent on target devices. The team will also need to build custom modules based on the Python programming language to extend the tool's functionality. Which automation tool should be used to meet these requirements?

A.Puppet

B.Ansible

C.NX-API

D.Chef

Answer: B

QUESTION 253

Refer to the exhibit. An engineer needs to implement streaming telemetry on a cisco MDS 9000 series switch. The requirement is for the show command data to be collected every 30 seconds and sent to receivers.

Which command must be added to the configuration meet this requirement?

A.Sensor-grp 200 sample-period 30000

B.Snsr-grp 200 sample-interval 30

C.Sensor-grp 200 sample-period 30

D.Snsr-grp 200 sample-interval 30000

Answer: D

QUESTION 254

A Cisco Nexus 9000 Series Switch experiences a startup configuration corruption. The engineer must implement a procedure to recover the backup configuration file from the switch. Which command set must be used?

A.1. Copy the running-configuration to the startup configuration.

2. Clear the current configuration of the switch.

3. Restart the device.

4. Copy a previously saved configuration file to the running configuration.

B.1. Clear the current configuration of the switch

2. Restart the device.

3. Copy the running configuration to the startup configuration

4. Copy a previously saved configuration file to the running configuration

C.1. Clear the current configuration of the switch

2. Restart the device.

3. Copy a previously saved configuration file to the running-configuration

4. Copy the running-configuration to the startup configuration.

D.1. Restarting device.

2. Copy the running-configuration file to a remote server.

3. Clear the current configuration of the switch.

4. Copy the running configuration to the startup configuration

Answer: C

QUESTION 255

An engineer must configure OSPF in the data center. The external routes have already been redistributed OSPF. The network must meet these criteria:

- The data centre servers must reach services in the cloud and the services behind the redistributed routes.

- The exit point toward the internet should be propagated only when there is a dynamically learned default route from the upstream router.

Which feature is required?

A.Default-information originate

B.Stubby area

C.Totally stubby area

D.Default-information originate always

Answer: A

QUESTION 256

What is a characteristic of the install all command on the cisco Nexus series switch?

A.Upgrades only certain modules

B.Automatically checks the image integrity

C.Impact data plan traffic

D.Continues the upgrade process if any step in the sequence fails

Answer: B

QUESTION 257

An engineer is using REST API calls to configure the cisco APIC. Which data structure must be used within a post message to receive a login token?

A.{"aaaUser":{"attributes":{"name":"apiuser","pwd":"cisco123"}}}

B.<aaaUser><name="apiuser"/><pwd="cisco123"/></aaaUser>

C.{aaaUser:{attributes:{name:apiuser,pwd:cisco123}}}

D.<aaaUser><name>apiuser</name><pwd>cisco123</pwd></aaaUser>

Answer: A

QUESTION 258

The EPLD update of the supervisor module has been scheduled for several Cisco MDS 9000 Series Switches. What will be the impact of the update?

A.All control plane traffic is stopped for the duration of the EPLD update and the switch remain operational for the duration of the upgrade.

B.The redundant supervisor lakes over while the EPLD update is in progress and there is no service disruption.

C.All traffic is stopped for the duration of the EPLD update and the switch is rebooted after the upgrade is completed.

D.The redundant supervisor lakes while the EPLD update is in progress and the switch is rebooted after the upgrade is completed.

Answer: C

QUESTION 259

An engineer configures an intersignt virtual application and must claim over 200 targets. The engineer starts the Claim target procedure. The engineer has prepared this initial comma- separated value file to provision the targets:

UCSFI,10.1.1.3,user-1,pwd5516b917

IMC,10.1.1.5/26,user-2,pwdc65b1c43f

HX,10.1.2.1/30,user-3,pwd39913690

UCSD,1.1.1.1.user-4,pwd5003e9d5

Which Information must be included In the comma-separated value flit to provision the targets?

A.FQON, AD name, IP address, email

B.location, address, name. password

C.certificate, user name, password. email

D.target type, hostname or P address, user name, password

Answer: D

QUESTION 260

What is an advantage of NFSv4 over Fibre Channel protocol?

A.Improved security

B.Lossless throughout

C.Congestion management

D.Uses IP transport

Answer: A

QUESTION 261

Which two configuration settings are available in the in the cisco UCS flmware Auto sync server policy?

A.User Notification

B.User Acknowledge

C.No Action

D.Delayed Action

E.Immediate Action

Answer: BC

QUESTION 262

An administrator is implementing DCNM so that events are triggered when monitored traffic exceeds the configured percent utilization threshold. The requirement is to configure a maximum limit of 39913690 bytes that applies directly to the statistics collected as a ratio of the total link capacity. Which DCNM performance monitoring configuration parameter must be implemented to achieve this result?

A.Absolution Values

B.Baseline

C.Utill%

D.Per port Monitoring

Answer: A

QUESTION 263

A network architect must redesign a data center network based on OSPFv2. The network must perform fast reconvergence between directly connected switches.

Which two actions must be taken to meet the requirements? (Choose two.)

A.Configure all links on AREA 0.

B.Implement a virtual link between the switches.

C.Use OSPF point-to-point links only.

D.Set low OSPF hello and DEAD timers.

E.Enable BFD for failure detection.

Answer: CE

QUESTION 264

Refer to the exhibit. A host with source address 10.10.10.10 sends traffic to multicast group 239.1.1.1. How do the vPC switches forward the multicast traffic?

A.If multicast traffic is received on Po11 Switch2, the traffic is forwarded out only one Po20.

B.If multicast traffic is received on Po10 Switch1, the traffic is forwarded out on Po1 and Po20.

C.If multicast traffic is received on Po11 and Switch2, the traffic is dropped.

D.If multicast traffic is received on Switch over the vPC peer-link, the traffic is dropped.

Answer: C

QUESTION 265

An engineer configured an environment that contains the vPC and non-vPC switches. However, it was noticed that the downstream non-vPC switches do not receive the same STP bridge ID from the upstream vPC switch peers. Which vPC feature must be implemented to ensure that vPC and non-vPC switches receive the same STP bridge ID from the upstream vPC switch peers?

A.System-mac 0123.4567.89ab

B.Peer-switch

C.VPC local role-priority 4000

D.Peer-gateway

Answer: B

QUESTION 266

A company is running a pair of cisco Nexus 7706 series switches as part of a data center segment. All network engineers have restricted read-Write access to the core switches.

A network engineer must a new FCoE VLAN to allow traffic from services toward FCoE storage. Which set of actions must be taken to meet these requirements?

A.1. Create a user-defined role and add the required privileges.

2. Assign a role to a user.

B.1. Add the required privilege to the VDC-admin role.

2. Commit the changes to the active user database.

C.1. Modify a network-operator role and add the required privileges.

2. Assign a VDC-operator role to a user.

D.1. Assign the network-admin role to a user.

2. Commit the role to the switch to the active user database

Answer: A

2023 Latest Braindump2go 350-601 PDF and 350-601 VCE Dumps Free Share:

https://drive.google.com/drive/folders/1M-Px6bHjOJgp4aPsLoYq-hgm90ZKxV_i?usp=sharing